Your Cart

x
0

MPP Corkscrew Model 3 & Y Front Upper Control Arms

$1,182.25
  • Availability: In Stock
Description

Please note the following items:

**This item will be shipped to our shop location in San Jose. THE DRIVEWAY will install the kit for you after you book an appointment

**SHIPPING IS INCLUDED IN THE PRICE. Item price is 1150.00 + 32.25 shipping.

**NO REFUNDS/RETURNS ALLOWED since MPP products are shipped from Canada/Germany. We cannot cancel your order once it's placed. Please call us (669-342-7072) if you have any questions or concerns regarding which part is appropriate for your vehicle.

**There are cases where the item may be backordered due to high popularity. We will update you via email if this is the case.

 

Go faster, without compromise.

The factory Model 3 and Model Y desperately need more camber on the track, but not much if any on the street. What if you could quickly dial in more camber when you get to the track, and then set it right back to stock before you drive home? Well, now you can.

  • CNC machined from billet 6061-T6 aluminum
  • Over 30% lighter than OEM arms, each arm weights under 4lbs
  • Made In Canada
  • Shim adjustment system for precise, repeatable adjustment – able to add or subtract up to 3° of camber in under 1 minute without removing wheels!
  • Sealed spherical bearings will last the lifetime of the car
  • Eliminate rubber bushings, feel a true connection to the road
  • No noises or wear, unlike common aftermarket arms which use spherical rod ends
  • Provided guide for toe adjustments to match camber settings for quick setup changes trackside
  • MPP was the first to use solid spherical bearings in aftermarket suspension arms. 

Fits these vehicles: All Model 3’s, All Model Y’s. 

The Model 3 and Model Y have a serious lack of front camber - and any of you that have taken your car to the track know that from the tire wear. When the sidewalls start becoming the tread of the tire, that's bad! Due to the suspension geometry, the car doesn't gain very much camber when the vehicle is lowered, or in roll. Statically shortening the front upper control arm helps both to increase the camber gain with suspension travel, and obviously to increase static camber. Lap time improvements are in the order of seconds when stepping from roughly -1 degree of camber to -3+. This is no small change!

 

Cameron's Performance Model 3 with prototype MPP Corkscrew Front Upper Control Arms


The camber adjustment mechanism uses shims - basically making camber settings infinitely repeatable. This is a huge advantage as it offers the end-user or the alignment shop the ability to drop in shims for a "track" alignment and then set it back to stock in a matter of minutes. MPP has a video coming soon that shows just how quickly a camber adjustment can be made (we're talking about less than one minute per side to make a change, the wheel doesn't even need to come off!). They have even prepared matching toe adjustments for various camber shim stacks. Say you want a street alignment with -1.5 degrees of camber, but want to turn it up to -3.4 degrees when you get to the track. No problem. Just take out the shims in the camber arm, turn the tie rod the exact number of turns specified in the instructions, and the toe will be within 1mm of where it was prior to the camber adjustment. When it's time to go home, simply pop the shims back in and set the tie rods back. We're talking about a few minutes per side to do this!

 

"MPP Corkscrew camber arms - named after the highest compression corner in North America where we ran these arms through their paces, and set a new EV Production Lap record doing it!"

"The arm has been sculpted for maximum clearance in vertical travel, and we were able to get the same amount of upwards travel as the OEM arm - an impressive feat considering we also had to add in a camber adjustment mechanism at the outer part of the arm. As an update in Late 2020, we've updated our design to be side to side specific to allow for additional travel clearance for the Tesla Model Y. We are able to do this WITH A PRICE DECREASE due to the investment in 5-axis machining. The finish of all of our products has also improved with the use of 5-axis machining. "

These arms include shims in 2mm steps to go between stock camber (around -1.2 degrees when lowered) and -3.4 degrees of camber. For those wanting less than OE camber, we can provide additional shims and longer bolts on request. The entire kit is made from CNC cut, North American sourced 6061 Aluminum billet.


RETURNS

Final sale. No returns or exchanges